Your search

Intensity interferometry, which was first used for obtaining ultra-high-resolution image information in astronomy in the 1960's and 1970's, is now being revived using modern detectors and electronics. This paper explores the possibility of wireless optical interferometry made possible by technological advancements in timing correlation, signal processing, and detector technology. If this can be achieved, then baselines of one to several kilometers may be possible in optical interferometry in the coming years. This would improve the resolution over the current generation of amplitude-based optical interferometers by a factor of at least ten. © COPYRIGHT SPIE. Downloading of the abstract is permitted for personal use only. © 2015 SPIE.

In recent years, speckle imaging has proven very useful for certain problems in single-Aperture high-resolution imaging, including searching for faint stellar companions near exoplanet host stars and for satellite imaging. These developments have largely been the result of the availability of electron-multiplying CCD cameras, which allow for greater sensitivity and better photometric linearity when compared with other detectors that have comparable speed. This in turn has led to an increased use for speckle imaging at mid-sized and large telescopes. Some results of these efforts will be discussed, and the outlook for the future of speckle will be given. © 2016 SPIE.

The Southern Connecticut Stellar Interferometer is an astronomical intensity interferometer consisting of two telescopes. Each is currently equipped with a single-photon avalanche diode (SPAD) detector, and an ultra-fast timing module correlates counts between both photon detectors. The interferometer has previously demonstrated intensity correlations using the 1-pixel SPADs and extremely narrow band pass filters but was limited in the amount of light that could be collected, and therefore the signal-to-noise ratio that could be achieved. SCSU's recent acquisition of an 8-pixel SPAD detector has allowed for a new possibility: a different wavelength of light could be directed towards each of the 8 pixels of the detector, thus conducting 8 independent intensity interferometry experiments at the same time, if this could be implemented at both telescopes. Using materials and resources available in the Astronomical Instrumentation Laboratory at Southern Connecticut State University, an optical system has been developed to work toward this goal but outfitting the first telescope in this way. The light from the telescope is collimated and directed toward a reflective diffraction grating. This is then re-imaged using a second lens and directed onto the pixels of the photon detector. These optical components have been placed inside an aluminum housing and can be mounted to the telescope for test observations. A status report will be given on the observations so far. If this can be replicated at the other telescope, the signal-to-noise ratio achievable with the instrument could be improved by a factor of 2.8.

Statistical characterization of secondary subsystems in binaries helps to distinguish between various scenarios of multiple-star formation. The Differential Speckle Survey Instrument was used at the Gemini-N telescope for several hours in 2015 July to probe the binarity of 25 secondary components in nearby solar-type binaries. Six new subsystems were resolved, with meaningful detection limits for the remaining targets. The large incidence of secondary subsystems agrees with other similar studies. The newly resolved subsystem HIP 115417 Ba,Bb causes deviations in the observed motion of the outer binary from which an astrometric orbit of Ba,Bb with a period of 117 years is deduced. © 2016. The American Astronomical Society. All rights reserved.

The high-spatial-resolution technique of speckle interferometry has been in use at Lowell Observatory's Discovery Channel Telescope since 2014 with the Dual-channel Stellar Speckle Imager (DSSI; Horch et al. 2009) as a visiting instrument. Using its standard bandpasses of 692 and 880nm, we have used highly efficient DSSI instrument to inspect over a thousand stellar systems over the course of 2014 (Horch et al. 2015). We have also demonstrated the usefulness of the DSSI@DCT system for resolved observations of high-altitude (>1,000 miles) man-made satellites in highly non-sidereal rate orbits.

Recent work with the NESSI speckle camera at Kitt Peak and the 'Alopeke speckle camera at Gemini-North indicates that speckle data reduction techniques can be successfully modified to produce high-resolution images over fields that are at least tens of arc seconds across. While these wide-field speckle image reconstructions are not diffraction-limited, the improvement in resolution over the seeing-limited case can be substantial. In this paper, we explore the application of these techniques to data taken with a small (0.6-m) telescope in an urban environment. Many telescopes located in urban communities, such as New Haven, Connecticut, where Southern Connecticut State University resides, have limited use scientifically due to substantial light pollution, poor seeing, poor telescope tracking, and other issues. We will present initial data using our set-up and discuss the potential for this approach for improving the imaging capabilities of small telescopes on our campus and beyond.

A limitation of the current generation of long baseline optical interferometers is the need to make the light interfere prior to detection. This is unlike the radio regime where signals can be recorded fast enough to use electronics to accomplish the same result. This paper describes a modern optical intensity interferometer based on electronics with picosecond timing resolution. The instrument will allow for portable optical interferometry with much larger baselines than currently possible by using existing large telescopes. With modern electronics, the limiting magnitude of the technique at a 4-m aperture size becomes competitive with some amplitude-based interferometers. The instrumentation will permit a wireless mode of operation with GPS clocking technology, extending the work to extremely large baselines. We discuss the basic observing strategy, a planned observational program at the Lowell Observatory 1.8-m and 1.0-m telescopes, and the science that can realistically be done with this instrumentation. © 2012 SPIE.

The NASA K2 mission is finding many high-value exoplanets and world-wide follow-up is ensuing. The NASA TESS mission will soon be launched, requiring additional ground-based observations as well. As a part of the NASA-NSFNN-EXPLORE program to enable exoplanet research, our group is building two new speckle interferometry cameras for the Kitt Peak WIYN 3.5-m telescope and the Gemini-N 8-m telescope. Modeled after the successful DSSI visitor instrument that has been used at these telescopes for many years, speckle observations provide the highest resolution images available today from any ground- or space-based single telescope. They are the premier method through which small, rocky exoplanets can be validated. Available for public use in early 2017, WIYNSPKL and GEMSPKL will obtain simultaneous images in two filters with fast EMCCD readout, "speckle" and “wide-field” imaging modes, and user support for proposal writing, observing, and data reduction. We describe the new cameras, their design, and their benefits for exoplanet follow-up, characterization, and validation. Funding for this project comes from the NASA Exoplanet Exploration Program and NASA HQ.

The Southern Connecticut Stellar Interferometer (SCSI) is a portable optical intensity interferometer located on the campus of Southern Connecticut State University in New Haven, Connecticut. Since its completion in 2016, the instrument has been used to take engineering data of bright stars. This paper will discuss the data collection and analysis methods, as well as the progress toward reliably measuring a significant stellar photon correlation. Vega has been the main star chosen for test observations to date because its diameter is well known by other methods, and it is not an extended source for the baselines used. The correlation peak in the processed data is compared to theoretical expectations. Given our expected sensitivity, a significant correlation peak is expected for small baselines (~2 m) to appear after a few hours of observation. So far, the observations indicate that the correlation peak is at the expected time delay, and the signal-to-noise ratio roughly scales as predicted.

Two new instruments are currently being built for the Gemini-North and WIYN telescopes. They are based on the existing DSSI (Differential Speckle Survey Instrument), but the new dual-channel instruments will have both speckle and "wide-field" imaging capabilities. Nearly identical copies of the instrument will be installed as a public access permanent loan at the Gemini-N and WIYN telescopes. Many exoplanet targets will come from the NASA K2 and TESS missions. The faint limiting magnitude, for speckle observations, will remain around 16 to 17th magnitude depending on observing conditions, while wide-field, high speed imaging should be able to go to 21+. For Gemini, the instrument will be remotely operable from either the mid-level facility at Hale Pohaku or the remote operations base in Hilo. © 2016 SPIE.

QWSSI, the Quad-camera Wavefront-Sensing Speckle Imager, is a next-generation speckle imager that is being developed for Lowell Observatory's 4.3-meter Discovery Channel Telescopes. The principle behind QWSSI is to extend the capabilities of the speckle camera currently resident at Lowell, the Differential Speckle Survey Instrument (DSSI), in two ways. First, while DSSI currently observes in two visible channels, QWSSI will simultaneously observe in six narrow-band channels: four in the visible (0.5-0.9um), and one each in J- and H-band (1.2 and 1.6um). Second, the visible light unused for speckle imaging is carefully preserved and feeds a wavefront sensor (WFS), which is also run simultaneously with the speckle imaging. Simulations by Löbb (2016) indicate WFS data will provide significant gains in exploring stellar multiplicity, with marked improvements in primary-secondary contrast ratios and inner working angle (Horch et al. 2018). QWSSI will also be mountable on one of the three 1-meter telescopes being installed on the NPOI Array for engineering tests and preliminary science observations. QWSSI will expand on the already considerable exoplanetary work of the speckle imagers DSSI, NESSI (@ WIYN), Alopeke (Gemini-N), and Zorro (Gemini-S), improving the discovery space for existing targets, as well opening up new regions of that discovery space with its NIR channels.

Speckle interferometry at Yale started in 1994 with a three-year program of observations at the Yale Southern Observatory at El Leoncito, Argentina. After this experience, we began a long-term program of speckle observations at the WIYN 3.5-m telescope at Kitt Peak National Observatory, first using a MAMA detector, then CCD and finally EMCCD technology. We describe the evolution of the program, its main results in terms of discovered components, orbital parameters and masses. While the Yale program ended in 2013, it provided the springboard for continued speckle efforts at WIYN, the Discovery Channel 4.3-m Telescope, and the Gemini 8.1-m Telescopes for binary star research, exoplanet science, and other projects. An important outcome of this research will be the incorporation of the soon to be released high-precision Gaia parallaxes into our observations.

Many hot Jupiters (HJs) are detected by the Doppler and transit techniques. From surveys using these two techniques, however, the measured HJ occurrence rates differ by a factor of two or more. Using the California Planet Survey sample and the Kepler sample, we investigate the causes for this difference in the HJ occurrence rate. First, we find that 12.8% ± 0.24% of HJs are misidentified in the Kepler mission because of photometric dilution and subgiant contamination. Second, we explore the differences between the Doppler sample and the Kepler sample that can account for the different HJ occurrence rate. Third, we discuss how to measure the fundamental HJ occurrence rates by synthesizing the results from the Doppler and Kepler surveys. The fundamental HJ occurrence rates are measures of the HJ occurrence rate as a function of stellar multiplicity and evolutionary stage, e.g., the HJ occurrence rate for single and multiple stars or for main-sequence and subgiant stars. While we find qualitative evidence that HJs occur less frequently in subgiants and multiple stellar systems, we conclude that our current knowledge of stellar properties and the stellar multiplicity rate is too limited for us to reach any quantitative result for the fundamental HJ occurrence rates. This concern extends to ηEarth, the occurrence rate of Earth-like planets. © 2015. The American Astronomical Society. All rights reserved.

While at first glance multi-star systems seem quite extreme, they are in fact the most common type of star system in our galaxy, throughout the stellar mass distribution. In particular, 40 to 50% of exoplanet host stars reside within multiple star systems. Given the degree to which initially undetected multiplicity has skewed Kepler results, high-resolution imaging of our nearby low-mass neighbors is necessary for both accurate characterization of transiting exoplanets, as well as a better understanding of stellar astrophysics. To address this frequent gap in our knowledge of exoplanet hosts, we will utilize speckle interferometry to directly image TESS exoplanet host candidates to complete our knowledge of individual star multiplicity. Our investigation will expand upon the speckle observations taken as a part of the POKEMON speckle survey of nearby M-dwarfs to better constrain the multiplicity of low-mass TESS exoplanet host candidates, and to constrain M-dwarf multiplicity by subtype across the entire M-dwarf sequence.

We are conducting a search for binary companions around 11 hot-Jupiter hosts from the Kilodegree Extremely Little Telescope (KELT) survey and a large comparison sample of stars shown by KELT to not host a transiting hot Jupiter. The primary stars are bright (7.5 < V < 11) and of similar distance from Earth (100 < d < 300 pc). In this paper, we present the results of our observations using the Differential Speckle Survey Instrument. We observed 9 of the 14 KELT planet hosts that are visible from the northern hemisphere and 51 comparison stars, discovering two new potential companions and re-observing two previously known possible binary systems and one confirmed binary system. We provide an estimate of the chance alignment probability for our observed candidate binaries. © 2017 The American Astronomical Society. All rights reserved.

Recent speckle observations performed at the Discovery Channel Telescope, the Gemini North Telescope, and the Special Astrophysical Observatory 6 m Telescope have permitted us to calculate the visual orbit of SB2 HD 114882 for the first time and to improve the visual orbits of two other SB2 systems, HD 30712 and HD 183255, using algorithms published by the authors of this research. Recently, new high-quality spectroscopic orbits have been obtained for these binaries by other authors. We determine their 3D orbits, individual masses, and orbital parallaxes, and present them in this paper. The parallaxes are compared with those available from the Gaia mission, and a comparison between the values confirms the precision of the results obtained here. © 2018. The American Astronomical Society. All rights reserved.

It is well known that in spectroscopic binary orbits, the inclination, the ascending node, and the semimajor axis remain undetermined, therefore the principal objective of this research is to establish an analytic methodology for the calculation of these parameters for spectroscopic binaries, both single-lined (SB1) and double-lined (SB2). In other words, the goal is to determine their “three-dimensional” orbits using a single speckle measurement (ρ, θ, t) and the parallax (π). Moreover, estimates of the individual masses of each system can also be obtained. The proposed algorithm was successfully applied to SB1 systems: YSC 148 (HD 37393) and CHR 225 (HD 34318), and SB2 systems: LSC 1 Aa1,2 (HD 200077) and Mkt 11 Aa, Ab (HD 358). In this late case, previously determined spectroscopic and visual orbits have been used to compare and contrast the results obtained from them with our results. The methodology presented is especially interesting for those cases in which it is only possible to resolve the spectroscopic binary in the zones of maximum angular separation by optical means thereby making it impossible to avail of sufficient observations in order to calculate the visual orbit. © Pleiades Publishing, Ltd. 2014.

As hundreds of gas giant planets have been discovered, we study how these planets form and evolve in different stellar environments, specifically in multiple stellar systems. In such systems, stellar companions may have a profound influence on gas giant planet formation and evolution via several dynamical effects such as truncation and perturbation. We select 84 Kepler Objects of Interest (KOIs) with gas giant planet candidates. We obtain high-angular resolution images using telescopes with adaptive optics (AO) systems. Together with the AO data, we use archival radial velocity data and dynamical analysis to constrain the presence of stellar companions. We detect 59 stellar companions around 40 KOIs for which we develop methods of testing their physical association. These methods are based on color information and galactic stellar population statistics. We find evidence of suppressive planet formation within 20 AU by comparing stellar multiplicity. The stellar multiplicity rate (MR) for planet host stars is 0+5-0% within 20 AU. In comparison, the stellar MR is 18% ± 2% for the control sample, i.e., field stars in the solar neighborhood. The stellar MR for planet host stars is 34% ± 8% for separations between 20 and 200 AU, which is higher than the control sample at 12% ± 2%. Beyond 200 AU, stellar MRs are comparable between planet host stars and the control sample. We discuss the implications of the results on gas giant planet formation and evolution. © 2015. The American Astronomical Society. All rights reserved.

It is well established that roughly half of all nearby solar-type stars have at least one companion. Stellar companions can have significant implications for the detection and characterization of exoplanets, including triggering false positives and masking the true radii of planets. Determining the fraction of exoplanet host stars that are also binaries allows us to better determine planetary characteristics as well as establish the relationship between binarity and planet formation. Using high angular resolution speckle imaging, we detect stellar companions within ∼1 arcsec of K2 planet-candidate host stars. Comparing our detected companion rate to TRILEGAL star count simulations and known detection limits of speckle imaging, we estimate the binary fraction of K2 planet host stars to be 40%-50%, similar to that of Kepler exoplanet hosts and field stars. © 2018. The American Astronomical Society. All rights reserved.